Scantronic 9800+ Manual do Utilizador

SCANTRONIC LTDUser GuideMicroprocessorIntruder AlarmSystem9 8 0 09 8 0 09 8 0 0

The Part Set function provides the user with the facility to set the systemwith only the detection allocated to Group B or C being armed. Circuits not

9The user can set or part set the system with selected alarm zones omittedfrom the system. (If zone is programmed by engineer for ‘Omit Enabled’.)Howe

If necessary, the user can omit a 24hr circuit when the system is unset. (Ifzone is programmed by engineer for ‘Omit Enable’.) To omit a 24hr circuitp

11On entering the premises the sounder will be emitting a continuous tone. Theuser should proceed immediately to the keypad via the prescribed entry r

If the user should stray from the prescribed entry route on normal entry tothe premises, a full alarm condition will occur, (external bells and intern

13Many local police authorities are concerned about the rising number of falsealarms raised at central stations by user error or system malfunction. T

14Remote Reset (Cont.)Call your alarm company centralstation, follow the verificationprocedure (usually a code name ornumber) and give the ‘ControlCod

15On entering the premises following an intrusion, a full alarm condition willexist. To cancel the alarm, the user should proceed directly to the remo

16The chime function is only available if programmed during installation andcan only be selected if the system is unset. When set to chime, the intern

17The system will accept up to four different user access codes, the first ofwhich is pre-programmed. The user can allocate or amend all four codes at

Access Code User private code (4 Digit) used to set, unset andprogramme the system.Automatic An optional automatic dialling unit fitted within theala

18Reviewing the Event Log With the alarm system in the ‘Day’ state, the user can scan the coded eventlog to obtain a record of system events. The even

19Sounder, Bell & Strobe TestThe user can test the operation of the internal and external sounders, bell andstrobe as follows:(c) External sounder

20System Walk TestThe user can ‘Walk Test’ the system and test the operation of each detectorcircuit (with the exception of panic alarms or fire circu

21System Faults & Alarm ConditionsTELEPHONE LINE FAULTIf your system is fitted with a remote signalling device which operates overthe standard tel

22System Fault Conditions (Cont.)BATTERY FAULTIf a battery fault condition occurs when the system is unset, a local alarmcondition will be initiated.

23Daytime Tamper AlarmThe alarm system automatically monitors the main control panel, keypads,external bell and circuit wiring and will automatically

24c1 to 8 Detector circuit open.t1 to 8 Circuit tamper open.o1 to 8 Detector circuit omitted (isolated).E1 to 8 Entry via a detector circuit.S1 to 8 D

25Your Circuit DescriptionZONE DESCRIPTION WHOLESYSTEMPARTSET BPARTSET COMITALLOWEDCHIME12345678Installed by (Engineer’s signature) . . . . . . . . .

26Service RecordDATE ENG REPORT

27COMPANY NAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ADDRESS . . . . . . . . . . . . . . . . . . . . . . .

1Section Title Page1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 OPERATOR CODES AND DISPLAYS . . . . . . . . .

SCANTRONIC LTDManufactured in the UK by Scantronic Ltd.Pt. No. 495665 Issue 2

The 9800 Electronic Intruder Alarm system uses the latest microprocessortechnology to provide a simple to operate, yet highly flexible system,suitable

Setting, unsetting and access to the system functions are normally inhibitedunless a four digit security code is entered via the remote keypad.The sys

Ensure that all doors and windows are secure, check that movementdetectors are not obstructed and proceed as follows:(c) Leave the premises by the pre

5Should the user attempt to set the system with one or more zones open, thesystem will not set. The internal sounder will emit an interrupted tone and

Your system may be fitted with an optional two-position keyswitch whichpermits keyholders to set and unset the alarm only. This facility must beprogra

7KEYSWITCH SETTING WITH ZONES OPENShould the user attempt to set the system with the keyswitch when one ormore zones are open, the system will not set